![]() ![]() I'm reconnecting the three harnesses that go to the switch panel and the light. Do the same for the bottom, sliding it in, bring the clip back over, snapping the clip, snapping the cable back in. Sliding the lock cable in and securing its tab, put the cable back into the housing. Then I'm going to put our screw back in at this point to hold the assembly in place. Reinstalling the door handle, I'm going to line up the four tabs on the back with the four rectangles on the door, and slide the assembly back into place. Then we can take our screwdriver and pry out the cable from the housing, pull it aside, and our handle assembly is going to slide forward and come out. The top cable will push up the bottom, and the bottom cable will come up through the top. You've got to use a flat blade screwdriver, a small one, and just pry on the clip itself, move it out a space, same at the bottom. There are two clips: one for the lock and one for the door handle, blue and pink. There's one Phillips head screw to remove. Undo another tab here, and the last tab here. Two go to the window switch pack, and another goes down to a door light at the bottom. I'm going to lift the panel up off of the door. There's a clip down here, and I'm going to do the same over here where the clip just came out. I'm going to give a little tug to the handle, get my fingers behind the panel, and just pry apart. After you take the screw out that's behind the door handle, you do have to pull the little bezel out. A Phillips screwdriver is all you need for all nine of those screws. I've got the screw covers off, exposing all nine of the screws: two on the back of the door, two on the very bottom of the door, two on the side, one in your handle assembly, and two below your grab handle. ![]() Use your flat blade screwdriver to pry up the seam and gently pull it out. There's two trim covers underneath the door handle. I'm going to take off the two trim covers here, the center pieces, and use a tiny flat screwdriver, or you can use a little pick. I'm going to use a piece of cloth to protect the paint while I pry the corner piece off here. The passenger side front door is the same process. The only tools you'll need are a small flat blade screwdriver, and a Phillips screwdriver. In this video, we're going to show you how to replace the driver's front door handle on this 2005 Hyundai Elantra. ![]() I hope this how-to video helps you out, and next time you need parts for your vehicle, think of. We're the company that's here for you on the Internet and in person.īrought to you by, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 88. Brought to you by your source for quality replacement parts and the best service on the Internet. Again we'll fast-forward as we just put those screws back in and tighten them up. Make sure your holes are lined up for my fasteners, then give it, pop the clips back in. Get my two cables, which then lock it in place. I'm going to snap it into place, then push back to lock it in. Putting the handle back in, there's four aligning notches. Then disconnect your clips from the handle. With a flat blade screwdriver, disconnect your blue clip and your pink clip. I'm going to use my knee to hold the door open while I give a little bit of a tug to the handle, enough to get some room with my hand, and feel around to the clips. Just speed up here as we remove the rest of the Phillips screws. We'll just pull the handle out and it'll slip right past it. I'm taking out the Phillips screw that holds the bezel into the door handle. I Located the door handle screw, the side screw, under the grab handle, under the grab handle, and the upper left. I'm just using a flat blade screwdriver: two, three. Taking off the door panel, I'm going to pop out my trim pieces that cover the fasteners. The only tools you'll need are a small flat blade screwdriver and a Phillips screwdriver. We show you the driver's side, byut the passenger side is the same procedure. Pretty much the same for any of this era Elantra. In this video, we're going to show you how to remove and reinstall a rear inside door handle on this 2005 Hyundai Elantra. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of. Brought to you by, your source for quality replacement parts and the best service on the Internet. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |